GoodingAluminium/K13/160/SV/IV

Gooding Aluminium Limited	Specification Clauses
	© 2006 Gooding Aluminium Limited

To complete the clause, select the appropriate wording from below. Highlighted text can be ‘dragged and dropped’ to save typing.

K13 RIGID SHEET FINE LININGS/PANELLING

160 PROPRIETARY . . . . . . . . . . .

Gooding Aluminium Ltd manufacture a wide range of aluminium panelling and fixings to suit most applications.
Plain, perforated and patterned sheet.
The GA Impressional and GA Anolight ranges of decorative cladding panels can be supplied with a variety of surface finishes.
A wide variety of profiled extrusions and an extensive selection of universal and architectural specific trims and profiles are also available.
Click on the name below to jump to the product and specification details
Perforated aluminium
Decorative cladding panels
Pan-L-Trim

Perforated aluminium
Click on the name below to jump to the product and specification details
Round holes/ staggered pitch
Round holes/ square pitch
Square holes/ square pitch
Hexagonal holes/ staggered pitch
Single slots / staggered pitch
Single slots / parallel pitch
5 slot sets / 45º arrangement
5 slot sets / 90º arrangement
Special patterns

Round holes/ staggered pitch
A range of aluminium sheets perforated with round holes with a staggered pitch pattern.
Hole diameter ranges from 1.3 mm to 31.7 mm.
Material thickness ranges from 1.2 mm to 3 mm.
Fixing:
Gooding Aluminium offer a range of fixings for use with aluminium sheets:
GA Ver T Fix
A system of vertically positioned fixing strips with integral hanging tabs that provide for the location and setting out of aluminium wall panels with a 2mm material thickness. A choice of single or double width fixing strips enables the panels to be arranged with or without shadow gap detailing.
GA Posi-Grip panel framing
An aluminium outer frame, manufactured as a single profile, with an inner ‘snap-in’ section which grips the panel over a significant surface area. Inserts are sized to allow for different material thickness. The panel framing incorporates dry mitred corners allowing for decorative / protective anodised finishes.
GA Posi-Grip ‘Instant Access’ panel framing
Panel framing with invisible and removable fixing capacity. The aluminium outer frame, manufactured as a single profile, with an inner ‘snap-in’ section, which grips the panel over a significant surface area. The units incorporate high quality stainless steel and nylon fixtures which provides an easily installed pressure engagement system. To allow for maximum lateral adjustment, factory fitted studs fixed to the reverse side of the frame are aligned through a continuously slotted opening. Friction bushes set into the opening surround securely grip the studs as the frame is positioned.
GA Extruded Alloy Squeeze Frames
Designed to provide maximum flexibility for use in a wide variety of fixing applications, including curved or rolled panels, the aluminium framing incorporate welded corner joints, providing additional tensile strength and rigidity, dimensional accuracy and clean slim outlines.
GA Gravity Frames
Designed for both ‘drop-in’ and screw fixing applications requiring a flanged fixing arrangement. The aluminium framing is designed to allow for rolling to diameters as small as 150mm, suitable for porthole type applications.
Consult with Gooding Aluminium technical literature at www.goodingalum.com for details.

Panels:

Manufacturer: Gooding Aluminium Ltd. 1, British Wharf, Landmann Way, London SE14 5RS. England. Tel: 020 8692 2255. Fax: 020 8469 0031. Email: sales@goodingalum.com Web: www.goodingalum.com
Product reference: Perforated aluminium - round holes/ staggered pitch
Board/ Panel type:
Ref: GA P1613 – Hole diameter 1.3 mm, Open area 20% - Material thickness 1.2 mm
Ref: GA P1650 – Hole diameter 1.6 mm, Open area 28% - Material thickness 1.2 mm
Ref: GA P1600 – Hole diameter 2.0 mm, Open area 30% - Material thickness 1.2 mm
Ref: GA P1601 – Hole diameter 3.0 mm, Open area 23% - Material thickness 1.2 mm
Ref: GA P1632 – Hole diameter 3.0 mm, Open area 23% - Material thickness 2.0 mm
Ref: GA P1651 – Hole diameter 3.0 mm, Open area 40% - Material thickness 1.2 mm
Ref: GA P1602 – Hole diameter 3.0 mm, Open area 40% - Material thickness 1.2 mm
Ref: GA P1603 – Hole diameter 3.0 mm, Open area 40% - Material thickness 2.0 mm
Ref: GA P1604 – Hole diameter 3.0 mm, Open area 40% - Material thickness 2.0 mm
Ref: GA P1605 – Hole diameter 3.0 mm, Open area 50% - Material thickness 1.2 mm
Ref: GA P1633 – Hole diameter 3.0 mm, Open area 50% - Material thickness 2.0 mm
Ref: GA P1694 – Hole diameter 4.7 mm, Open area 21% - Material thickness 1.2 mm
Ref: GA P1695 – Hole diameter 4.7 mm, Open area 21% - Material thickness 2.0 mm
Ref: GA P1652 – Hole diameter 4.7 mm, Open area 40% - Material thickness 1.2 mm
Ref: GA P1670 – Hole diameter 4.7 mm, Open area 40% - Material thickness 1.2 mm
Ref: GA P1606 – Hole diameter 4.7 mm, Open area 40% - Material thickness 2.0 mm
Ref: GA P1607 – Hole diameter 4.7 mm, Open area 40% - Material thickness 2.0 mm
Ref: GA P1648 – Hole diameter 4.7 mm, Open area 40% - Material thickness 3.0 mm
Ref: GA P1649 – Hole diameter 4.7 mm, Open area 40% - Material thickness 3.0 mm
Ref: GA P1608 – Hole diameter 4.7 mm, Open area 49% - Material thickness 1.2 mm
Ref: GA P1609 – Hole diameter 4.7 mm, Open area 49% - Material thickness 2.0 mm
Ref: GA P1696 – Hole diameter 6.3 mm, Open area 29% - Material thickness 1.2 mm
Ref: GA P1697 – Hole diameter 6.3 mm, Open area 29% - Material thickness 2.0 mm
Ref: GA P1653 – Hole diameter 6.3 mm, Open area 40% - Material thickness 1.2 mm
Ref: GA P1671 – Hole diameter 6.3 mm, Open area 40% - Material thickness 1.2 mm
Ref: GA P1683 – Hole diameter 6.3 mm, Open area 40% - Material thickness 2.0 mm
Ref: GA P1681 – Hole diameter 6.3 mm, Open area 40% - Material thickness 2.0 mm
Ref: GA P1640 – Hole diameter 6.3 mm, Open area 40% - Material thickness 3.0 mm
Ref: GA P1641 – Hole diameter 6.3 mm, Open area 40% - Material thickness 3.0 mm
Ref: GA P1698 – Hole diameter 6.3 mm, Open area 49% - Material thickness 1.2 mm
Ref: GA P1699 – Hole diameter 6.3 mm, Open area 49% - Material thickness 2.0 mm
Ref: GA P1654 – Hole diameter 9.5 mm, Open area 35% - Material thickness 1.2 mm
Ref: GA P1625 – Hole diameter 9.5 mm, Open area 35% - Material thickness 1.2 mm
Ref: GA P1684 – Hole diameter 9.5 mm, Open area 35% - Material thickness 2.0 mm
Ref: GA P1685 – Hole diameter 9.5 mm, Open area 35% - Material thickness 2.0 mm
Ref: GA P1642 – Hole diameter 9.5 mm, Open area 35% - Material thickness 3.0 mm
Ref: GA P1643 – Hole diameter 9.5 mm, Open area 35% - Material thickness 3.0 mm
Ref: GA P1656 – Hole diameter 12.0 mm, Open area 40% - Material thickness 1.2 mm
Ref: GA P1687 – Hole diameter 12.0 mm, Open area 40% - Material thickness 1.2 mm
Ref: GA P1686 – Hole diameter 12.0 mm, Open area 40% - Material thickness 2.0 mm
Ref: GA P1688 – Hole diameter 12.0 mm, Open area 40% - Material thickness 2.0 mm
Ref: GA P1689 – Hole diameter 15.0 mm, Open area 40% - Material thickness 1.2 mm
Ref: GA P1690 – Hole diameter 15.0 mm, Open area 40% - Material thickness 2.0 mm
Ref: GA P1691 – Hole diameter 15.0 mm, Open area 40% - Material thickness 2.0 mm
Ref: GA P1692 – Hole diameter 19.0 mm, Open area 40% - Material thickness 2.0 mm
Ref: GA P1672 – Hole diameter 22.2 mm, Open area 44% - Material thickness 2.0 mm
Ref: GA P1673 – Hole diameter 22.2 mm, Open area 44% - Material thickness 3.0 mm
Ref: GA P1626 – Hole diameter 31.7 mm, Open area 44% - Material thickness 2.0 mm
Ref: GA P1636 – Hole diameter 31.7 mm, Open area 44% - Material thickness 3.0 mm
Thickness: 1.2 mm / 2.0 mm / 3.0 mm

Core material: Not applicable
Facing: For alternative surface finishes refer to www.goodingalum.com
Moisture content at time of fixing: Not applicable.

Edge treatment: For details refer to www.goodingalum.com

Installation:

Method of fixing panels:
GA Posi-Grip panel framing
Framing Profile - GA PG251 – Width 25mm - to suit material thickness 1.2mm.
Framing Profile - GA PG252 – Width 25mm - to suit material thickness 2.0mm.
Framing Profile - GA PG351 – Width 35mm - to suit material thickness 1.2mm.
Framing Profile - GA PG352 – Width 35mm - to suit material thickness 2.0mm.
Panel Divider - GA PGD251 – Width 25mm - to suit material thickness 1.2mm.
Panel Divider - GA PGD252 – Width 25mm - to suit material thickness 2.0mm.
GA Posi-Grip ‘Instant Access’ panel framing
Framing Profile - GA PGIA251 – Width 25mm - to suit material thickness 1.2mm.
Framing Profile - GA PGIA252 – Width 25mm - to suit material thickness 2.0mm.
Framing Profile - GA PGIA351 – Width 35mm - to suit material thickness 1.2mm.
Framing Profile - GA PGIA352 – Width 35mm - to suit material thickness 2.0mm.
GA Extruded Alloy Squeeze Frames
Framing Profile - GA SF251 – Leg 25mm - to suit material thickness 1.2mm.
Framing Profile - GA SF252 – Leg 25mm - to suit material thickness 2.0mm.
Framing Profile - GA SF401 – Leg 40mm - to suit material thickness 1.2mm.
Framing Profile - GA SF402 – Leg 40mm - to suit material thickness 2.0mm.
Panel Divider - GA SFD201 – o/a Width 20mm - to suit material thickness 1.2mm.
Panel Divider - GA SFD252 – o/a Width 25mm - to suit material thickness 2.0mm.
GA Gravity Frames
Framing Profile - GA GF191 – Flange width 19mm - to suit material thickness 1.2mm.
Framing Profile - GA GF192 – Flange width 19mm - to suit material thickness 2.0mm.
Joint treatment: For details refer to www.goodingalum.com

Round holes/ square pitch
A range of aluminium sheets perforated with round holes with a square pitch pattern.
Hole diameter ranges from 1.3 mm to 31.7 mm.
Material thickness ranges from 1.2 mm to 3 mm.
Fixing:
Gooding Aluminium offer a range of fixings for use with aluminium sheets:
GA Ver T Fix
A system of vertically positioned fixing strips with integral hanging tabs that provide for the location and setting out of aluminium wall panels with a 2mm material thickness. A choice of single or double width fixing strips enables the panels to be arranged with or without shadow gap detailing.
GA Posi-Grip panel framing
An aluminium outer frame, manufactured as a single profile, with an inner ‘snap-in’ section which grips the panel over a significant surface area. Inserts are sized to allow for different material thickness. The panel framing incorporates dry mitred corners allowing for decorative / protective anodised finishes.
GA Posi-Grip ‘Instant Access’ panel framing
Panel framing with invisible and removable fixing capacity. The aluminium outer frame, manufactured as a single profile, with an inner ‘snap-in’ section, which grips the panel over a significant surface area. The units incorporate high quality stainless steel and nylon fixtures which provides an easily installed pressure engagement system. To allow for maximum lateral adjustment, factory fitted studs fixed to the reverse side of the frame are aligned through a continuously slotted opening. Friction bushes set into the opening surround securely grip the studs as the frame is positioned.
GA Extruded Alloy Squeeze Frames
Designed to provide maximum flexibility for use in a wide variety of fixing applications, including curved or rolled panels, the aluminium framing incorporate welded corner joints, providing additional tensile strength and rigidity, dimensional accuracy and clean slim outlines.
GA Gravity Frames
Designed for both ‘drop-in’ and screw fixing applications requiring a flanged fixing arrangement. The aluminium framing is designed to allow for rolling to diameters as small as 150mm, suitable for porthole type applications.
Consult with Gooding Aluminium technical literature at www.goodingalum.com for details.

Panels:

Core material: Not applicable
Facing: For alternative surface finishes refer to www.goodingalum.com
Moisture content at time of fixing: Not applicable.

Edge treatment: For details refer to www.goodingalum.com

Installation:

Method of fixing panels:
GA Posi-Grip panel framing
Framing Profile - GA PG251 – Width 25mm - to suit material thickness 1.2mm.
Framing Profile - GA PG252 – Width 25mm - to suit material thickness 2.0mm.
Framing Profile - GA PG351 – Width 35mm - to suit material thickness 1.2mm.
Framing Profile - GA PG352 – Width 35mm - to suit material thickness 2.0mm.
Panel Divider - GA PGD251 – Width 25mm - to suit material thickness 1.2mm.
Panel Divider - GA PGD252 – Width 25mm - to suit material thickness 2.0mm.
GA Posi-Grip ‘Instant Access’ panel framing
Framing Profile - GA PGIA251 – Width 25mm - to suit material thickness 1.2mm.
Framing Profile - GA PGIA252 – Width 25mm - to suit material thickness 2.0mm.
Framing Profile - GA PGIA351 – Width 35mm - to suit material thickness 1.2mm.
Framing Profile - GA PGIA352 – Width 35mm - to suit material thickness 2.0mm.
GA Extruded Alloy Squeeze Frames
Framing Profile - GA SF251 – Leg 25mm - to suit material thickness 1.2mm.
Framing Profile - GA SF252 – Leg 25mm - to suit material thickness 2.0mm.
Framing Profile - GA SF401 – Leg 40mm - to suit material thickness 1.2mm.
Framing Profile - GA SF402 – Leg 40mm - to suit material thickness 2.0mm.
Panel Divider - GA SFD201 – o/a Width 20mm - to suit material thickness 1.2mm.
Panel Divider - GA SFD252 – o/a Width 25mm - to suit material thickness 2.0mm.
GA Gravity Frames
Framing Profile - GA GF191 – Flange width 19mm - to suit material thickness 1.2mm.
Framing Profile - GA GF192 – Flange width 19mm - to suit material thickness 2.0mm.
Joint treatment: For details refer to www.goodingalum.com

Square holes/ square pitch
A range of aluminium sheets perforated with square holes with a square pitch pattern.
Hole sizes ranges from 3.0 mm sq. to 19.0 mm sq.
Material thickness ranges from 1.2 mm to 3 mm.
Fixing:
Gooding Aluminium offer a range of fixings for use with aluminium sheets:
GA Ver T Fix
A system of vertically positioned fixing strips with integral hanging tabs that provide for the location and setting out of aluminium wall panels with a 2mm material thickness. A choice of single or double width fixing strips enables the panels to be arranged with or without shadow gap detailing.
GA Posi-Grip panel framing
An aluminium outer frame, manufactured as a single profile, with an inner ‘snap-in’ section which grips the panel over a significant surface area. Inserts are sized to allow for different material thickness. The panel framing incorporates dry mitred corners allowing for decorative / protective anodised finishes.
GA Posi-Grip ‘Instant Access’ panel framing
Panel framing with invisible and removable fixing capacity. The aluminium outer frame, manufactured as a single profile, with an inner ‘snap-in’ section, which grips the panel over a significant surface area. The units incorporate high quality stainless steel and nylon fixtures which provides an easily installed pressure engagement system. To allow for maximum lateral adjustment, factory fitted studs fixed to the reverse side of the frame are aligned through a continuously slotted opening. Friction bushes set into the opening surround securely grip the studs as the frame is positioned.
GA Extruded Alloy Squeeze Frames
Designed to provide maximum flexibility for use in a wide variety of fixing applications, including curved or rolled panels, the aluminium framing incorporate welded corner joints, providing additional tensile strength and rigidity, dimensional accuracy and clean slim outlines.
GA Gravity Frames
Designed for both ‘drop-in’ and screw fixing applications requiring a flanged fixing arrangement. The aluminium framing is designed to allow for rolling to diameters as small as 150mm, suitable for porthole type applications.
Consult with Gooding Aluminium technical literature at www.goodingalum.com for details.

Panels:

Core material: Not applicable
Facing: For alternative surface finishes refer to www.goodingalum.com
Moisture content at time of fixing: Not applicable.

Edge treatment: For details refer to www.goodingalum.com

Installation:

Hexagonal holes/ staggered pitch
A range of aluminium sheets perforated with hexagonal holes with a staggered pitch pattern.
Hole sizes ranges from 6.0 x 6.9 mm to 9.0 x 10.4 mm.
Material thickness ranges from 1.2 mm to 2 mm.
Fixing:
Gooding Aluminium offer a range of fixings for use with aluminium sheets:
GA Ver T Fix
A system of vertically positioned fixing strips with integral hanging tabs that provide for the location and setting out of aluminium wall panels with a 2mm material thickness. A choice of single or double width fixing strips enables the panels to be arranged with or without shadow gap detailing.
GA Posi-Grip panel framing
An aluminium outer frame, manufactured as a single profile, with an inner ‘snap-in’ section which grips the panel over a significant surface area. Inserts are sized to allow for different material thickness. The panel framing incorporates dry mitred corners allowing for decorative / protective anodised finishes.
GA Posi-Grip ‘Instant Access’ panel framing
Panel framing with invisible and removable fixing capacity. The aluminium outer frame, manufactured as a single profile, with an inner ‘snap-in’ section, which grips the panel over a significant surface area. The units incorporate high quality stainless steel and nylon fixtures which provides an easily installed pressure engagement system. To allow for maximum lateral adjustment, factory fitted studs fixed to the reverse side of the frame are aligned through a continuously slotted opening. Friction bushes set into the opening surround securely grip the studs as the frame is positioned.
GA Extruded Alloy Squeeze Frames
Designed to provide maximum flexibility for use in a wide variety of fixing applications, including curved or rolled panels, the aluminium framing incorporate welded corner joints, providing additional tensile strength and rigidity, dimensional accuracy and clean slim outlines.
GA Gravity Frames
Designed for both ‘drop-in’ and screw fixing applications requiring a flanged fixing arrangement. The aluminium framing is designed to allow for rolling to diameters as small as 150mm, suitable for porthole type applications.
Consult with Gooding Aluminium technical literature at www.goodingalum.com for details.

Panels:

Core material: Not applicable
Facing: For alternative surface finishes refer to www.goodingalum.com
Moisture content at time of fixing: Not applicable.

Edge treatment: For details refer to www.goodingalum.com

Installation:

Single slots / staggered pitch
A range of aluminium sheets perforated with single slots with a staggered pitch pattern.
Hole sizes ranges from 20.0 x 4.0 mm to 25.0 x 6.0 mm.
Material thickness ranges from 1.2 mm to 2 mm.
Fixing:
Gooding Aluminium offer a range of fixings for use with aluminium sheets:
GA Ver T Fix
A system of vertically positioned fixing strips with integral hanging tabs that provide for the location and setting out of aluminium wall panels with a 2mm material thickness. A choice of single or double width fixing strips enables the panels to be arranged with or without shadow gap detailing.
GA Posi-Grip panel framing
An aluminium outer frame, manufactured as a single profile, with an inner ‘snap-in’ section which grips the panel over a significant surface area. Inserts are sized to allow for different material thickness. The panel framing incorporates dry mitred corners allowing for decorative / protective anodised finishes.
GA Posi-Grip ‘Instant Access’ panel framing
Panel framing with invisible and removable fixing capacity. The aluminium outer frame, manufactured as a single profile, with an inner ‘snap-in’ section, which grips the panel over a significant surface area. The units incorporate high quality stainless steel and nylon fixtures which provides an easily installed pressure engagement system. To allow for maximum lateral adjustment, factory fitted studs fixed to the reverse side of the frame are aligned through a continuously slotted opening. Friction bushes set into the opening surround securely grip the studs as the frame is positioned.
GA Extruded Alloy Squeeze Frames
Designed to provide maximum flexibility for use in a wide variety of fixing applications, including curved or rolled panels, the aluminium framing incorporate welded corner joints, providing additional tensile strength and rigidity, dimensional accuracy and clean slim outlines.
GA Gravity Frames
Designed for both ‘drop-in’ and screw fixing applications requiring a flanged fixing arrangement. The aluminium framing is designed to allow for rolling to diameters as small as 150mm, suitable for porthole type applications.
Consult with Gooding Aluminium technical literature at www.goodingalum.com for details.

Panels:

Core material: Not applicable
Facing: For alternative surface finishes refer to www.goodingalum.com
Moisture content at time of fixing: Not applicable.

Edge treatment: For details refer to www.goodingalum.com

Installation:

Single slots / parallel pitch
A range of aluminium sheets perforated with single slots with a parallel pitch pattern.
Hole sizes ranges from 20.0 x 4.0 mm to 25.0 x 6.0 mm.
Material thickness ranges from 1.2 mm to 2 mm.
Fixing:
Gooding Aluminium offer a range of fixings for use with aluminium sheets:
GA Ver T Fix
A system of vertically positioned fixing strips with integral hanging tabs that provide for the location and setting out of aluminium wall panels with a 2mm material thickness. A choice of single or double width fixing strips enables the panels to be arranged with or without shadow gap detailing.
GA Posi-Grip panel framing
An aluminium outer frame, manufactured as a single profile, with an inner ‘snap-in’ section which grips the panel over a significant surface area. Inserts are sized to allow for different material thickness. The panel framing incorporates dry mitred corners allowing for decorative / protective anodised finishes.
GA Posi-Grip ‘Instant Access’ panel framing
Panel framing with invisible and removable fixing capacity. The aluminium outer frame, manufactured as a single profile, with an inner ‘snap-in’ section, which grips the panel over a significant surface area. The units incorporate high quality stainless steel and nylon fixtures which provides an easily installed pressure engagement system. To allow for maximum lateral adjustment, factory fitted studs fixed to the reverse side of the frame are aligned through a continuously slotted opening. Friction bushes set into the opening surround securely grip the studs as the frame is positioned.
GA Extruded Alloy Squeeze Frames
Designed to provide maximum flexibility for use in a wide variety of fixing applications, including curved or rolled panels, the aluminium framing incorporate welded corner joints, providing additional tensile strength and rigidity, dimensional accuracy and clean slim outlines.
GA Gravity Frames
Designed for both ‘drop-in’ and screw fixing applications requiring a flanged fixing arrangement. The aluminium framing is designed to allow for rolling to diameters as small as 150mm, suitable for porthole type applications.
Consult with Gooding Aluminium technical literature at www.goodingalum.com for details.

Panels:

Core material: Not applicable
Facing: For alternative surface finishes refer to www.goodingalum.com
Moisture content at time of fixing: Not applicable.

Edge treatment: For details refer to www.goodingalum.com

Installation:

5 slot sets / 45º arrangement
A range of aluminium sheets perforated with 5 slot sets with a 45º arrangement.
Hole sizes ranges from 20.0 x 1.7 mm to 25.0 x 2.5 mm.
Material thickness ranges from 1.2 mm to 2 mm.
Fixing:
Gooding Aluminium offer a range of fixings for use with aluminium sheets:
GA Ver T Fix
A system of vertically positioned fixing strips with integral hanging tabs that provide for the location and setting out of aluminium wall panels with a 2mm material thickness. A choice of single or double width fixing strips enables the panels to be arranged with or without shadow gap detailing.
GA Posi-Grip panel framing
An aluminium outer frame, manufactured as a single profile, with an inner ‘snap-in’ section which grips the panel over a significant surface area. Inserts are sized to allow for different material thickness. The panel framing incorporates dry mitred corners allowing for decorative / protective anodised finishes.
GA Posi-Grip ‘Instant Access’ panel framing
Panel framing with invisible and removable fixing capacity. The aluminium outer frame, manufactured as a single profile, with an inner ‘snap-in’ section, which grips the panel over a significant surface area. The units incorporate high quality stainless steel and nylon fixtures which provides an easily installed pressure engagement system. To allow for maximum lateral adjustment, factory fitted studs fixed to the reverse side of the frame are aligned through a continuously slotted opening. Friction bushes set into the opening surround securely grip the studs as the frame is positioned.
GA Extruded Alloy Squeeze Frames
Designed to provide maximum flexibility for use in a wide variety of fixing applications, including curved or rolled panels, the aluminium framing incorporate welded corner joints, providing additional tensile strength and rigidity, dimensional accuracy and clean slim outlines.
GA Gravity Frames
Designed for both ‘drop-in’ and screw fixing applications requiring a flanged fixing arrangement. The aluminium framing is designed to allow for rolling to diameters as small as 150mm, suitable for porthole type applications.
Consult with Gooding Aluminium technical literature at www.goodingalum.com for details.

Panels:

Core material: Not applicable
Facing: For alternative surface finishes refer to www.goodingalum.com
Moisture content at time of fixing: Not applicable.

Edge treatment: For details refer to www.goodingalum.com

Installation:

5 slot sets / 90º arrangement
A range of aluminium sheets perforated with 5 slot sets with a 90º arrangement.
Hole sizes ranges from 20.0 x 1.7 mm to 25.0 x 2.5 mm.
Material thickness ranges from 1.2 mm to 2 mm.
Fixing:
Gooding Aluminium offer a range of fixings for use with aluminium sheets:
GA Ver T Fix
A system of vertically positioned fixing strips with integral hanging tabs that provide for the location and setting out of aluminium wall panels with a 2mm material thickness. A choice of single or double width fixing strips enables the panels to be arranged with or without shadow gap detailing.
GA Posi-Grip panel framing
An aluminium outer frame, manufactured as a single profile, with an inner ‘snap-in’ section which grips the panel over a significant surface area. Inserts are sized to allow for different material thickness. The panel framing incorporates dry mitred corners allowing for decorative / protective anodised finishes.
GA Posi-Grip ‘Instant Access’ panel framing
Panel framing with invisible and removable fixing capacity. The aluminium outer frame, manufactured as a single profile, with an inner ‘snap-in’ section, which grips the panel over a significant surface area. The units incorporate high quality stainless steel and nylon fixtures which provides an easily installed pressure engagement system. To allow for maximum lateral adjustment, factory fitted studs fixed to the reverse side of the frame are aligned through a continuously slotted opening. Friction bushes set into the opening surround securely grip the studs as the frame is positioned.
GA Extruded Alloy Squeeze Frames
Designed to provide maximum flexibility for use in a wide variety of fixing applications, including curved or rolled panels, the aluminium framing incorporate welded corner joints, providing additional tensile strength and rigidity, dimensional accuracy and clean slim outlines.
GA Gravity Frames
Designed for both ‘drop-in’ and screw fixing applications requiring a flanged fixing arrangement. The aluminium framing is designed to allow for rolling to diameters as small as 150mm, suitable for porthole type applications.
Consult with Gooding Aluminium technical literature at www.goodingalum.com for details.

Panels:

Core material: Not applicable
Facing: For alternative surface finishes refer to www.goodingalum.com
Moisture content at time of fixing: Not applicable.

Edge treatment: For details refer to www.goodingalum.com

Installation:

Special patterns
A range of aluminium sheets perforated with special patterns.
Hole sizes ranges from 3.0 mm sq. to 15.0 mm oval.
Material thickness ranges from 1.2 mm to 2 mm.
Fixing:
Gooding Aluminium offer a range of fixings for use with aluminium sheets:
GA Ver T Fix
A system of vertically positioned fixing strips with integral hanging tabs that provide for the location and setting out of aluminium wall panels with a 2mm material thickness. A choice of single or double width fixing strips enables the panels to be arranged with or without shadow gap detailing.
GA Posi-Grip panel framing
An aluminium outer frame, manufactured as a single profile, with an inner ‘snap-in’ section which grips the panel over a significant surface area. Inserts are sized to allow for different material thickness. The panel framing incorporates dry mitred corners allowing for decorative / protective anodised finishes.
GA Posi-Grip ‘Instant Access’ panel framing
Panel framing with invisible and removable fixing capacity. The aluminium outer frame, manufactured as a single profile, with an inner ‘snap-in’ section, which grips the panel over a significant surface area. The units incorporate high quality stainless steel and nylon fixtures which provides an easily installed pressure engagement system. To allow for maximum lateral adjustment, factory fitted studs fixed to the reverse side of the frame are aligned through a continuously slotted opening. Friction bushes set into the opening surround securely grip the studs as the frame is positioned.
GA Extruded Alloy Squeeze Frames
Designed to provide maximum flexibility for use in a wide variety of fixing applications, including curved or rolled panels, the aluminium framing incorporate welded corner joints, providing additional tensile strength and rigidity, dimensional accuracy and clean slim outlines.
GA Gravity Frames
Designed for both ‘drop-in’ and screw fixing applications requiring a flanged fixing arrangement. The aluminium framing is designed to allow for rolling to diameters as small as 150mm, suitable for porthole type applications.
Consult with Gooding Aluminium technical literature at www.goodingalum.com for details.

Panels:

Core material: Not applicable
Facing: For alternative surface finishes refer to www.goodingalum.com
Moisture content at time of fixing: Not applicable.

Edge treatment: For details refer to www.goodingalum.com

Installation:

Method of fixing panels:
GA Posi-Grip panel framing
Framing Profile - GA PG251 – Width 25mm - to suit material thickness 1.2mm.
Framing Profile - GA PG252 – Width 25mm - to suit material thickness 2.0mm.
Framing Profile - GA PG351 – Width 35mm - to suit material thickness 1.2mm.
Framing Profile - GA PG352 – Width 35mm - to suit material thickness 2.0mm.
Panel Divider - GA PGD251 – Width 25mm - to suit material thickness 1.2mm.
Panel Divider - GA PGD252 – Width 25mm - to suit material thickness 2.0mm.
GA Posi-Grip ‘Instant Access’ panel framing
Framing Profile - GA PGIA251 – Width 25mm - to suit material thickness 1.2mm.
Framing Profile - GA PGIA252 – Width 25mm - to suit material thickness 2.0mm.
Framing Profile - GA PGIA351 – Width 35mm - to suit material thickness 1.2mm.
Framing Profile - GA PGIA352 – Width 35mm - to suit material thickness 2.0mm.
GA Extruded Alloy Squeeze Frames
Framing Profile - GA SF251 – Leg 25mm - to suit material thickness 1.2mm.
Framing Profile - GA SF252 – Leg 25mm - to suit material thickness 2.0mm.
Framing Profile - GA SF401 – Leg 40mm - to suit material thickness 1.2mm.
Framing Profile - GA SF402 – Leg 40mm - to suit material thickness 2.0mm.
Panel Divider - GA SFD201 – o/a Width 20mm - to suit material thickness 1.2mm.
Panel Divider - GA SFD252 – o/a Width 25mm - to suit material thickness 2.0mm.
Joint treatment: For details refer to www.goodingalum.com

Decorative cladding panels
Click on the name below to jump to the product and specification details.
GA Impressional (Dome) Decorative cladding panels
GA Impressional Perforated (Dome) Decorative cladding panels
GA Impressional (Square) Decorative cladding panels
GA Impressional (Plus) Decorative cladding panels
GA Impressional (Minus) Decorative cladding panels
GA Anolight Decorative profiled sheets
GA Anolight Decorative profiled perforated sheets
Patterned sheet (Lozenge designs)
Patterned sheet (Textured)
Woven micromesh
Plain anodised
Satin brushed sheet (one side)
Plain mill finish

GA Impressional (Dome) Decorative cladding panels
A range of aluminium round dome patterned sheets for use as decorative cladding panels.
Pattern sizes ranges from 6.0 mm dia x 1.5 mm high to 65 mm dia x 4 mm high.
Material thickness ranges from 1.2 mm to 2 mm.
Fixing:
Gooding Aluminium offer a range of fixings for use with aluminium sheets:
GA Ver T Fix
A system of vertically positioned fixing strips with integral hanging tabs that provide for the location and setting out of aluminium wall panels with a 2mm material thickness. A choice of single or double width fixing strips enables the panels to be arranged with or without shadow gap detailing.
GA Posi-Grip ‘Instant Access’ panel framing
Panel framing with invisible and removable fixing capacity. The aluminium outer frame, manufactured as a single profile, with an inner ‘snap-in’ section, which grips the panel over a significant surface area. The units incorporate high quality stainless steel and nylon fixtures which provides an easily installed pressure engagement system. To allow for maximum lateral adjustment, factory fitted studs fixed to the reverse side of the frame are aligned through a continuously slotted opening. Friction bushes set into the opening surround securely grip the studs as the frame is positioned.
GA Panel-Fix
An invisible wall panel fixing system, manufactured aluminium and available in stock mill finish. The system comprises of an extruded aluminium alloy section with a rigid interlocking grip. Lateral adjustment enables panels to be accurately and quickly slid into position. Units are pre-drilled with countersunk holes at 200mm centres and supplied in lengths up to 2500mm.
Gooding Aluminium Ltd can also supply a comprehensive range of aluminium extruded profiles.
Consult with Gooding Aluminium technical literature at www.goodingalum.com for details.

Panels:

Manufacturer: Gooding Aluminium Ltd. 1, British Wharf, Landmann Way, London SE14 5RS. England. Tel: 020 8692 2255. Fax: 020 8469 0031. Email: sales@goodingalum.com Web: www.goodingalum.com
Product reference: GA Impressional (Dome) Decorative cladding panels
Board/ Panel type:
Pattern height: 1.5 mm, Pattern size: 6 mm dia, Pattern pitch: 25 mm
Ref: GA IMM601 – Mill finish – Material thickness 1.2 mm
Ref: GA IMS601 – Matt anodised finish – Material thickness 1.2 mm

Pattern height: 1.5 mm, Pattern size: 6 mm dia, Pattern pitch: 15 mm,
Ref: GA IMM691 – Mill finish – Material thickness 1.2 mm
Ref: GA IMS691 – Matt anodised finish – Material thickness 1.2 mm

Pattern height: 2.0 mm, Pattern size: 10 mm dia, Pattern pitch: 35 mm
Ref: GA IMM101 – Mill finish – Material thickness 1.2 mm
Ref: GA IMS101 – Matt anodised finish – Material thickness 1.2 mm

Pattern height: 2.0 mm, Pattern size: 20 mm dia, Pattern pitch: 50 mm
Ref: GA IMM201 – Mill finish – Material thickness 1.2 mm
Ref: GA IMS201 – Matt anodised finish – Material thickness 1.2 mm
Ref: GA IMM202 – Mill finish – Material thickness 2.0 mm
Ref: GA IMS202 – Matt anodised finish – Material thickness 2.0 mm

Pattern height: 3.0 mm, Pattern size: 31 mm dia, Pattern pitch: 100 mm
Ref: GA IMM311 – Mill finish – Material thickness 1.2 mm
Ref: GA IMS311 – Matt anodised finish – Material thickness 1.2 mm
Ref: GA IMM312 – Mill finish – Material thickness 2.0 mm
Ref: GA IMS312 – Matt anodised finish – Material thickness 2.0 mm

Pattern height: 3.5 mm, Pattern size: 50 mm dia, Pattern pitch: 150 mm
Ref: GA IMM501 – Mill finish – Material thickness 1.2 mm
Ref: GA IMS501 – Matt anodised finish – Material thickness 1.2 mm
Ref: GA IMM502 – Mill finish – Material thickness 2.0 mm
Ref: GA IMS502 – Matt anodised finish – Material thickness 2.0 mm

Pattern height: 4.0 mm, Pattern size: 65 mm dia, Pattern pitch: 175 mm
Ref: GA IMM651 – Mill finish – Material thickness 1.2 mm
Ref: GA IMS651 – Matt anodised finish – Material thickness 1.2 mm
Ref: GA IMM652 – Mill finish – Material thickness 2.0 mm
Ref: GA IMS652 – Matt anodised finish – Material thickness 2.0 mm
Thickness: 1.2 mm / 2.0 mm

Core material: Not applicable
Facing: For alternative surface finishes refer to www.goodingalum.com
Moisture content at time of fixing: Not applicable

Edge treatment: For details refer to www.goodingalum.com

Installation:

Method of fixing panels:
GA Posi-Grip 'Instant Access' panel framing
GA Ver T Fix (for panels with double folded edge returns)
GA Panel-Fix (when using panels with backing boards)
Joint treatment: For details refer to www.goodingalum.com

GA Impressional Perforated (Dome) Decorative cladding panels
A range of aluminium round dome perforated patterned sheets for use as decorative cladding panels.
Pattern sizes ranges from 20.0 mm dia x 2.0 mm high to 31 mm dia x 3.0 mm high.
Hole dia: 2.0 mm, Open area: 30%.
Material thickness 1.2 mm.
Fixing:
Gooding Aluminium offer a range of fixings for use with aluminium sheets:
GA Ver T Fix
A system of vertically positioned fixing strips with integral hanging tabs that provide for the location and setting out of aluminium wall panels with a 2mm material thickness. A choice of single or double width fixing strips enables the panels to be arranged with or without shadow gap detailing.
GA Posi-Grip ‘Instant Access’ panel framing
Panel framing with invisible and removable fixing capacity. The aluminium outer frame, manufactured as a single profile, with an inner ‘snap-in’ section, which grips the panel over a significant surface area. The units incorporate high quality stainless steel and nylon fixtures which provides an easily installed pressure engagement system. To allow for maximum lateral adjustment, factory fitted studs fixed to the reverse side of the frame are aligned through a continuously slotted opening. Friction bushes set into the opening surround securely grip the studs as the frame is positioned.
GA Panel-Fix
An invisible wall panel fixing system, manufactured aluminium and available in stock mill finish. The system comprises of an extruded aluminium alloy section with a rigid interlocking grip. Lateral adjustment enables panels to be accurately and quickly slid into position. Units are pre-drilled with countersunk holes at 200mm centres and supplied in lengths up to 2500mm.
Gooding Aluminium Ltd can also supply a comprehensive range of aluminium extruded profiles.
Consult with Gooding Aluminium technical literature at www.goodingalum.com for details.

Panels:

Manufacturer: Gooding Aluminium Ltd. 1, British Wharf, Landmann Way, London SE14 5RS. England. Tel: 020 8692 2255. Fax: 020 8469 0031. Email: sales@goodingalum.com Web: www.goodingalum.com
Product reference: GA Impressional Perforated (Dome) Decorative cladding panels
Board/ Panel type:
Pattern height: 2.0 mm, Pattern size: 20 mm dia, Hole dia: 2.0 mm, Open area: 30%, Pattern pitch: 50 mm,
Ref: GA PIMM201 – Mill finish
Ref: GA PIMS201 – Matt anodised finish

Pattern height 3.0 mm, Pattern size: 31 mm dia, Hole dia: 2.0 mm, Open area: 30%, Pattern pitch: 100 mm
Ref: GA PIMM311 – Mill finish
Ref: GA PIMS311 – Matt anodised finish
Thickness: 1.2 mm

Core material: Not applicable
Facing: For alternative surface finishes refer to www.goodingalum.com
Moisture content at time of fixing: Not applicable.

Edge treatment: For details refer to www.goodingalum.com

Installation:

GA Impressional (Square) Decorative cladding panels
A range of aluminium raised square patterned sheets for use as decorative cladding panels.
Pattern sizes ranges from 10.0mm square x 2.0 mm high to 20.0 mm sq x 2.0 mm high.
Material thickness ranges from 1.2 mm to 2.0 mm.
Fixing:
Gooding Aluminium offer a range of fixings for use with aluminium sheets:
GA Ver T Fix
A system of vertically positioned fixing strips with integral hanging tabs that provide for the location and setting out of aluminium wall panels with a 2mm material thickness. A choice of single or double width fixing strips enables the panels to be arranged with or without shadow gap detailing.
GA Posi-Grip ‘Instant Access’ panel framing
Panel framing with invisible and removable fixing capacity. The aluminium outer frame, manufactured as a single profile, with an inner ‘snap-in’ section, which grips the panel over a significant surface area. The units incorporate high quality stainless steel and nylon fixtures which provides an easily installed pressure engagement system. To allow for maximum lateral adjustment, factory fitted studs fixed to the reverse side of the frame are aligned through a continuously slotted opening. Friction bushes set into the opening surround securely grip the studs as the frame is positioned.
GA Panel-Fix
An invisible wall panel fixing system, manufactured aluminium and available in stock mill finish. The system comprises of an extruded aluminium alloy section with a rigid interlocking grip. Lateral adjustment enables panels to be accurately and quickly slid into position. Units are pre-drilled with countersunk holes at 200mm centres and supplied in lengths up to 2500mm.
Gooding Aluminium Ltd can also supply a comprehensive range of aluminium extruded profiles.
Consult with Gooding Aluminium technical literature at www.goodingalum.com for details.

Panels:

Manufacturer: Gooding Aluminium Ltd. 1, British Wharf, Landmann Way, London SE14 5RS. England. Tel: 020 8692 2255. Fax: 020 8469 0031. Email: sales@goodingalum.com Web: www.goodingalum.com
Product reference: GA Impressional (Square) Decorative cladding panels
Board/ Panel type:
Pattern height: 2.0 mm, Pattern size: 10 mm sq, Pattern pitch: 35 mm
Ref: GA IMSQM101 – Mill finish – Material thickness 1.2 mm
Ref: GA IMSQS101 – Matt anodised finish – Material thickness 1.2 mm

Pattern height: 2.0 mm, Pattern size: 15 mm sq, Pattern pitch: 35 mm
Ref: GA IMSQM151 – Mill finish – Material thickness 1.2 mm
Ref: GA IMSQS151 – Matt anodised finish – Material thickness 1.2 mm
Ref: GA IMSQM152 – Mill finish – Material thickness 2.0 mm
Ref: GA IMSQS152 – Matt anodised finish – Material thickness 2.0 mm

Pattern height: 2.0 mm, Pattern size: 20 mm sq, Pattern pitch: 50 mm
Ref: GA IMSQM202 – Mill finish – Material thickness 2.0 mm
Ref: GA IMSQS202 – Matt anodised finish – Material thickness 2.0 mm
Thickness: 1.2 mm / 2.0 mm

Core material: Not applicable
Facing: For alternative surface finishes refer to www.goodingalum.com
Moisture content at time of fixing: Not applicable.

Edge treatment: For details refer to www.goodingalum.com

Installation:

GA Impressional (Plus) Decorative cladding panels
A range of aluminium raised ‘plus’ patterned sheets for use as decorative cladding panels.
Pattern height: 1.5 mm, Pattern size: 30 mm, Pattern pitch: 60 mm
Fixing:
Gooding Aluminium offer a range of fixings for use with aluminium sheets:
GA Ver T Fix
A system of vertically positioned fixing strips with integral hanging tabs that provide for the location and setting out of aluminium wall panels with a 2mm material thickness. A choice of single or double width fixing strips enables the panels to be arranged with or without shadow gap detailing.
GA Posi-Grip ‘Instant Access’ panel framing
Panel framing with invisible and removable fixing capacity. The aluminium outer frame, manufactured as a single profile, with an inner ‘snap-in’ section, which grips the panel over a significant surface area. The units incorporate high quality stainless steel and nylon fixtures which provides an easily installed pressure engagement system. To allow for maximum lateral adjustment, factory fitted studs fixed to the reverse side of the frame are aligned through a continuously slotted opening. Friction bushes set into the opening surround securely grip the studs as the frame is positioned.
GA Panel-Fix
An invisible wall panel fixing system, manufactured aluminium and available in stock mill finish. The system comprises of an extruded aluminium alloy section with a rigid interlocking grip. Lateral adjustment enables panels to be accurately and quickly slid into position. Units are pre-drilled with countersunk holes at 200mm centres and supplied in lengths up to 2500mm.
Gooding Aluminium Ltd can also supply a comprehensive range of aluminium extruded profiles.
Consult with Gooding Aluminium technical literature at www.goodingalum.com for details.

Panels:

Manufacturer: Gooding Aluminium Ltd. 1, British Wharf, Landmann Way, London SE14 5RS. England. Tel: 020 8692 2255. Fax: 020 8469 0031. Email: sales@goodingalum.com Web: www.goodingalum.com
Product reference: GA Impressional (Plus) Decorative cladding panels
Board/ Panel type:
Pattern height: 1.5 mm, Pattern size: 30 mm, Pattern pitch: 60 mm
Ref: GA IMXM301 – Mill finish
Ref: GA IMXS301 – Matt anodised finish
Thickness: 1.2 mm

Core material: Not applicable
Facing: For alternative surface finishes refer to www.goodingalum.com
Moisture content at time of fixing: Not applicable.

Edge treatment: For details refer to www.goodingalum.com

Installation:

GA Impressional (Minus) Decorative cladding panels
A range of aluminium raised ‘minus’ patterned sheets for use as decorative cladding panels.
Pattern height: 2.5 mm, Pattern size: 45 x 12 mm, Pattern pitch: 70 x 35 mm
Fixing:
Gooding Aluminium offer a range of fixings for use with aluminium sheets:
GA Ver T Fix
A system of vertically positioned fixing strips with integral hanging tabs that provide for the location and setting out of aluminium wall panels with a 2mm material thickness. A choice of single or double width fixing strips enables the panels to be arranged with or without shadow gap detailing.
GA Posi-Grip ‘Instant Access’ panel framing
Panel framing with invisible and removable fixing capacity. The aluminium outer frame, manufactured as a single profile, with an inner ‘snap-in’ section, which grips the panel over a significant surface area. The units incorporate high quality stainless steel and nylon fixtures which provides an easily installed pressure engagement system. To allow for maximum lateral adjustment, factory fitted studs fixed to the reverse side of the frame are aligned through a continuously slotted opening. Friction bushes set into the opening surround securely grip the studs as the frame is positioned.
GA Panel-Fix
An invisible wall panel fixing system, manufactured aluminium and available in stock mill finish. The system comprises of an extruded aluminium alloy section with a rigid interlocking grip. Lateral adjustment enables panels to be accurately and quickly slid into position. Units are pre-drilled with countersunk holes at 200mm centres and supplied in lengths up to 2500mm.
Gooding Aluminium Ltd can also supply a comprehensive range of aluminium extruded profiles.
Consult with Gooding Aluminium technical literature at www.goodingalum.com for details.

Panels:

Manufacturer: Gooding Aluminium Ltd. 1, British Wharf, Landmann Way, London SE14 5RS. England. Tel: 020 8692 2255. Fax: 020 8469 0031. Email: sales@goodingalum.com Web: www.goodingalum.com
Product reference: GA Impressional (Minus) Decorative cladding panels
Board/ Panel type:
Pattern height: 2.5 mm, Pattern size: 45 x 12 mm, Pattern pitch: 70 x 35 mm
Ref: GA IMM002 – Mill finish
Ref: GA IMS002 – Matt anodised finish
Thickness: 2.0 mm
Core material: Not applicable
Facing: For alternative surface finishes refer to www.goodingalum.com
Moisture content at time of fixing: Not applicable.

Edge treatment: For details refer to www.goodingalum.com

Installation:

GA Anolight Decorative profiled sheets
A range of aluminium profiled sheets for use as decorative cladding panels.
Profile height ranges from 5.0 mm to 10.0 mm, Cover width ranges from 550 mm to 1000 mm.
Gooding Aluminium Ltd can also supply a comprehensive range of aluminium extruded profiles.
Consult with Gooding Aluminium technical literature at www.goodingalum.com for details.

Panels:

Manufacturer: Gooding Aluminium Ltd. 1, British Wharf, Landmann Way, London SE14 5RS. England. Tel: 020 8692 2255. Fax: 020 8469 0031. Email: sales@goodingalum.com Web: www.goodingalum.com
Product reference: GA Anolight Decorative profiled sheets
Board/ Panel type:
Profile height: 5.5 mm, Cover width: 550 mm
Ref: GA AA21 – Matt finish
Profile height: 5.0 mm, Cover width: 790 mm
Ref: GA AA55 – Matt finish
Profile height: 5.0 mm, Cover width: 570 mm
Ref: GA AACP20 – Matt finish
Profile height: 10.0 mm, Cover width: 1000 mm
Ref: GA AA21 – Matt finish
Thickness: 1.0 mm

Core material: Not applicable
Facing: For alternative surface finishes refer to www.goodingalum.com
Moisture content at time of fixing: Not applicable.

Edge treatment: For details refer to www.goodingalum.com

Installation:

Method of fixing panels:
Fixing by screws to rear timber battening or surfacing
Joint treatment: For details refer to www.goodingalum.com

GA Anolight Decorative profiled perforated sheets
A range of aluminium profiled perforated sheets for use as decorative cladding panels.
Profile height ranges from 5.0 mm to 10.0 mm, Cover width ranges from 550 mm to 1000 mm.
Gooding Aluminium Ltd can also supply a comprehensive range of aluminium extruded profiles.
Consult with Gooding Aluminium technical literature at www.goodingalum.com for details.

Panels:

Manufacturer: Gooding Aluminium Ltd. 1, British Wharf, Landmann Way, London SE14 5RS. England. Tel: 020 8692 2255. Fax: 020 8469 0031. Email: sales@goodingalum.com Web: www.goodingalum.com
Product reference: GA Anolight Decorative profiled perforated sheets
Board/ Panel type:
Hole dia: 2.0 mm, Open area: 20%, Profile height: 5.5 mm, Cover width: 550 mm
Ref: GAP AA21 – Matt finish
Hole dia: 2.0 mm, Open area: 20%, Profile height: 5.0 mm, Cover width: 790 mm
Ref: GAP AA55 – Matt finish
Hole dia: 2.0 mm, Open area: 20%, Profile height: 5.0 mm, Cover width: 570 mm
Ref: GAP AACP20 – Matt finish
Hole dia: 2.0 mm, Open area: 20%, Profile height: 10.0 mm, Cover width: 1000 mm
Ref: GAP AA41 – Matt finish
Thickness: 1.2 mm
Core material: Not applicable
Facing: For alternative surface finishes refer to www.goodingalum.com
Moisture content at time of fixing: Not applicable.

Edge treatment: For details refer to www.goodingalum.com

Installation:

Method of fixing panels:
Fixing by screws to rear timber battening or surfacing
Joint treatment: For details refer to www.goodingalum.com

Patterned sheet (Lozenge designs)
Click on the name below to jump to the product and specification details.
Tread grip

Tread grip
A range of aluminium ‘lozenge’ design profiled sheets for use as decorative cladding panels.
Available in Material thickness 2.0 mm.
Gooding Aluminium Ltd can also supply a comprehensive range of aluminium extruded profiles.
Consult with Gooding Aluminium technical literature at www.goodingalum.com for details.

Panels:

Core material: Not applicable
Facing: For alternative surface finishes refer to www.goodingalum.com
Moisture content at time of fixing: Not applicable.

Edge treatment: For details refer to www.goodingalum.com

Installation:

Method of fixing panels:
Fixing by screws to rear timber battening or surfacing
Joint treatment: For details refer to www.goodingalum.com

Patterned sheet (Textured)
Click on the name below to jump to the product and specification details.
Axis
Vertex

Axis
An aluminium textured sheet for use as decorative cladding panels.
Available in material thicknesses of 1.0 mm.
Fixing:
Gooding Aluminium offer a range of fixings for use with aluminium sheets:
GA Ver T Fix
A system of vertically positioned fixing strips with integral hanging tabs that provide for the location and setting out of aluminium wall panels with a 2mm material thickness. A choice of single or double width fixing strips enables the panels to be arranged with or without shadow gap detailing.
GA Posi-Grip ‘Instant Access’ panel framing
Panel framing with invisible and removable fixing capacity. The aluminium outer frame, manufactured as a single profile, with an inner ‘snap-in’ section, which grips the panel over a significant surface area. The units incorporate high quality stainless steel and nylon fixtures which provides an easily installed pressure engagement system. To allow for maximum lateral adjustment, factory fitted studs fixed to the reverse side of the frame are aligned through a continuously slotted opening. Friction bushes set into the opening surround securely grip the studs as the frame is positioned.
GA Panel-Fix
An invisible wall panel fixing system, manufactured aluminium and available in stock mill finish. The system comprises of an extruded aluminium alloy section with a rigid interlocking grip. Lateral adjustment enables panels to be accurately and quickly slid into position. Units are pre-drilled with countersunk holes at 200mm centres and supplied in lengths up to 2500mm.
Consult with Gooding Aluminium technical literature at www.goodingalum.com for details.

Panels:

Manufacturer: Gooding Aluminium Ltd. 1, British Wharf, Landmann Way, London SE14 5RS. England. Tel: 020 8692 2255. Fax: 020 8469 0031. Email: sales@goodingalum.com Web: www.goodingalum.com
Product reference: Patterned sheet (Textured) Axis
Board/ Panel type:
Ref: GA AXM21 – Mill finish
Ref: GA AXS21 – Ano-Sil anodised finish
Thickness: 1.0 mm

Core material: Not applicable
Facing: For alternative surface finishes refer to www.goodingalum.com
Moisture content at time of fixing: Not applicable.

Edge treatment: For details refer to www.goodingalum.com

Installation:

Vertex
An aluminium textured sheet for use as decorative cladding panels.
Available in material thicknesses of 1.0 mm.
Fixing:
Gooding Aluminium offer a range of fixings for use with aluminium sheets:
GA Ver T Fix
A system of vertically positioned fixing strips with integral hanging tabs that provide for the location and setting out of aluminium wall panels with a 2mm material thickness. A choice of single or double width fixing strips enables the panels to be arranged with or without shadow gap detailing.
GA Posi-Grip ‘Instant Access’ panel framing
Panel framing with invisible and removable fixing capacity. The aluminium outer frame, manufactured as a single profile, with an inner ‘snap-in’ section, which grips the panel over a significant surface area. The units incorporate high quality stainless steel and nylon fixtures which provides an easily installed pressure engagement system. To allow for maximum lateral adjustment, factory fitted studs fixed to the reverse side of the frame are aligned through a continuously slotted opening. Friction bushes set into the opening surround securely grip the studs as the frame is positioned.
GA Panel-Fix
An invisible wall panel fixing system, manufactured aluminium and available in stock mill finish. The system comprises of an extruded aluminium alloy section with a rigid interlocking grip. Lateral adjustment enables panels to be accurately and quickly slid into position. Units are pre-drilled with countersunk holes at 200mm centres and supplied in lengths up to 2500mm.
Consult with Gooding Aluminium technical literature at www.goodingalum.com for details.

Panels:

Manufacturer: Gooding Aluminium Ltd. 1, British Wharf, Landmann Way, London SE14 5RS. England. Tel: 020 8692 2255. Fax: 020 8469 0031. Email: sales@goodingalum.com Web: www.goodingalum.com
Product reference: Patterned sheet (Textured) Vertex
Board/ Panel type:
Ref: GA VXM21 – Mill finish
Ref: GA VXS21 – Ano-Sil anodised finish
Thickness: 1.0 mm

Core material: Not applicable
Facing: For alternative surface finishes refer to www.goodingalum.com
Moisture content at time of fixing: Not applicable.

Edge treatment: For details refer to www.goodingalum.com

Installation:

Woven micromesh
A fine aluminium woven mesh sheet for use as an optional backing to perforated sheet panels.
Available in material thicknesses of 0.28 mm.
Fixing:
Gooding Aluminium offer a range of fixings for use with aluminium sheets:
Consult with Gooding Aluminium technical literature at www.goodingalum.com for details.

Panels:

Core material: Not applicable
Facing: For alternative surface finishes refer to www.goodingalum.com
Moisture content at time of fixing: Not applicable.

Edge treatment: For details refer to www.goodingalum.com

Installation:

Method of fixing panels: For details refer to www.goodingalum.com
Joint treatment: For details refer to www.goodingalum.com

Plain anodised
A range of aluminium plain anodised sheets for use as decorative cladding panels.
Available in material thicknesses from 1.0 mm to 3.0 mm.
Fixing:
Gooding Aluminium offer a range of fixings for use with aluminium sheets:
GA Ver T Fix
A system of vertically positioned fixing strips with integral hanging tabs that provide for the location and setting out of aluminium wall panels with a 2mm material thickness. A choice of single or double width fixing strips enables the panels to be arranged with or without shadow gap detailing.
GA Posi-Grip ‘Instant Access’ panel framing
Panel framing with invisible and removable fixing capacity. The aluminium outer frame, manufactured as a single profile, with an inner ‘snap-in’ section, which grips the panel over a significant surface area. The units incorporate high quality stainless steel and nylon fixtures which provides an easily installed pressure engagement system. To allow for maximum lateral adjustment, factory fitted studs fixed to the reverse side of the frame are aligned through a continuously slotted opening. Friction bushes set into the opening surround securely grip the studs as the frame is positioned.
GA Panel-Fix
An invisible wall panel fixing system, manufactured aluminium and available in stock mill finish. The system comprises of an extruded aluminium alloy section with a rigid interlocking grip. Lateral adjustment enables panels to be accurately and quickly slid into position. Units are pre-drilled with countersunk holes at 200mm centres and supplied in lengths up to 2500mm.
Consult with Gooding Aluminium technical literature at www.goodingalum.com for details.

Panels:

Board/ Panel type:
Ref: GA SA10 – Material thickness 1.0 mm
Ref: GA SA20 – Material thickness 1.5 mm
Ref: GA SA21 – Material thickness 3.0 mm
Thickness: 1.0 mm / 1.5 mm / 3.0 mm

Core material: Not applicable
Facing: For alternative surface finishes refer to www.goodingalum.com
Moisture content at time of fixing: Not applicable.

Edge treatment: For details refer to www.goodingalum.com

Installation:

Satin brushed sheet (one side)
A range of aluminium satin brushed sheets for use as decorative cladding panels.
Available in material thicknesses from 1.2 mm to 2.0 mm.
Fixing:
Gooding Aluminium offer a range of fixings for use with aluminium sheets:
GA Ver T Fix
A system of vertically positioned fixing strips with integral hanging tabs that provide for the location and setting out of aluminium wall panels with a 2mm material thickness. A choice of single or double width fixing strips enables the panels to be arranged with or without shadow gap detailing.
GA Posi-Grip ‘Instant Access’ panel framing
Panel framing with invisible and removable fixing capacity. The aluminium outer frame, manufactured as a single profile, with an inner ‘snap-in’ section, which grips the panel over a significant surface area. The units incorporate high quality stainless steel and nylon fixtures which provides an easily installed pressure engagement system. To allow for maximum lateral adjustment, factory fitted studs fixed to the reverse side of the frame are aligned through a continuously slotted opening. Friction bushes set into the opening surround securely grip the studs as the frame is positioned.
GA Panel-Fix
An invisible wall panel fixing system, manufactured aluminium and available in stock mill finish. The system comprises of an extruded aluminium alloy section with a rigid interlocking grip. Lateral adjustment enables panels to be accurately and quickly slid into position. Units are pre-drilled with countersunk holes at 200mm centres and supplied in lengths up to 2500mm.
Consult with Gooding Aluminium technical literature at www.goodingalum.com for details.

Panels:

Core material: Not applicable
Facing: For alternative surface finishes refer to www.goodingalum.com
Moisture content at time of fixing: Not applicable.

Edge treatment: For details refer to www.goodingalum.com

Installation:

Plain mill finish
A range of aluminium plain mill finish sheets for use as decorative cladding panels.
Available in material thicknesses from 0.8 mm to 4.0 mm.
Fixing:
Gooding Aluminium offer a range of fixings for use with aluminium sheets:
GA Ver T Fix
A system of vertically positioned fixing strips with integral hanging tabs that provide for the location and setting out of aluminium wall panels with a 2mm material thickness. A choice of single or double width fixing strips enables the panels to be arranged with or without shadow gap detailing.
GA Posi-Grip ‘Instant Access’ panel framing
Panel framing with invisible and removable fixing capacity. The aluminium outer frame, manufactured as a single profile, with an inner ‘snap-in’ section, which grips the panel over a significant surface area. The units incorporate high quality stainless steel and nylon fixtures which provides an easily installed pressure engagement system. To allow for maximum lateral adjustment, factory fitted studs fixed to the reverse side of the frame are aligned through a continuously slotted opening. Friction bushes set into the opening surround securely grip the studs as the frame is positioned.
GA Panel-Fix
An invisible wall panel fixing system, manufactured aluminium and available in stock mill finish. The system comprises of an extruded aluminium alloy section with a rigid interlocking grip. Lateral adjustment enables panels to be accurately and quickly slid into position. Units are pre-drilled with countersunk holes at 200mm centres and supplied in lengths up to 2500mm.
Consult with Gooding Aluminium technical literature at www.goodingalum.com for details.

Panels:

Manufacturer: Gooding Aluminium Ltd. 1, British Wharf, Landmann Way, London SE14 5RS. England. Tel: 020 8692 2255. Fax: 020 8469 0031. Email: sales@goodingalum.com Web: www.goodingalum.com
Product reference: Plain mill finish aluminium sheet
Board/ Panel type:
Ref: GA 1536 – Material thickness 0.8 mm
Ref: GA 1505 – Material thickness 1.2 mm
Ref: GA 1537 – Material thickness 1.2 mm
Ref: GA 1506 – Material thickness 1.5 mm
Ref: GA 1538 – Material thickness 1.5 mm
Ref: GA 1507 – Material thickness 2.0 mm
Ref: GA 1539 – Material thickness 2.0 mm
Ref: GA 1509 – Material thickness 3.0 mm
Ref: GA 1541 – Material thickness 3.0 mm
Ref: GA 1542 – Material thickness 4.0 mm
Thickness: 0.8 mm / 1.2 mm / 1.5 mm / 2.0 mm / 3.0 mm / 4.0 mm
Core material: Not applicable
Facing: For alternative surface finishes refer to www.goodingalum.com
Moisture content at time of fixing: Not applicable.

Edge treatment: For details refer to www.goodingalum.com

Installation:

Pan-L-Trim
GA Pan-L-Trim is a sleek, stylish fixing and alloy framing option for wall lining panels.
Designed for fast track applications at airports, offices and retail outlets, these profiles are rapidly and ‘secretly’ fixed.
Providing clear scope for creative freedom with a multitude of design choices these elegant high quality aluminium alloy extrusions accept a wide variety of board depths from 20 to 6mm.
Designed to be seen, GA Pan-L-Trim is the edge retention system that focuses the eye on its clean and smoothly radiused surfaces and edges. Available in either mill or anodised finishes.
The extensive series of co-ordinated Pan-L-Trim profiles incorporate tapering flanges for secure ‘grip-it’ fixing. To further help with on-site installation there are also longitudinal grooves in the fixing flanges for easy drill fit location.
Consult with Gooding Aluminium technical literature at www.goodingalum.com for details.

Installation:

Method of fixing panels:
Manufacturer: Gooding Aluminium Ltd. 1, British Wharf, Landmann Way, London SE14 5RS. England. Tel: 020 8692 2255. Fax: 020 8469 0031. Email: sales@goodingalum.com Web: www.goodingalum.com
Product reference: GA Pan-L-Trim
Ref: GA PLT2001 – 20mm In Line Panel Trim
Ref: GA PLT2002 – 20mm External Corner Panel Trim
Ref: GA PLT2003 – 20mm Panel End Trim
Ref: GA PLT2004 – 20mm Internal Corner Panel Trim

Ref: GA PLT1601 – 16mm In Line Panel Trim
Ref: GA PLT1602 – 16mm External Corner Panel Trim
Ref: GA PLT1603 – 16mm Panel End Trim
Ref: GA PLT1604 – 16mm Internal Corner Panel Trim
Ref: GA PLT13/16 – 16mm Easy Fit 2 Part Corner Trim

Ref: GA PLT1301 – 13mm In Line Panel Trim
Ref: GA PLT1302 – 13mm External Corner Panel Trim
Ref: GA PLT1303 – 13mm Panel End Trim
Ref: GA PLT1304 – 13mm Internal Corner Panel Trim
Ref: GA PLT13/16 – 13mm Easy Fit 2 Part Corner Trim

Ref: GA PLT601 – 6mm In Line Panel Trim
Ref: GA PLT602 – 6mm External Corner Panel Trim
Ref: GA PLT603 – 6mm Panel End Trim
Ref: GA PLT604 – 6mm Internal Corner Panel Trim
Joint treatment: For details refer to www.goodingalum.com